Loading...

Ballscrew Guys > Shin Nippon Koki (SNK)

Ballscrew Guys are specialists in on-site repair and refurbishment of Shin Nippon Koki (SNK) Lathe and Machining Center linear motion systems including ball screw assemblies and linear way guides.

Please contact us to troubleshoot your issue and follow up with a service request with travel and work estimates. See our flat rate specials and inquire about travel splits if your down time is flexible.

Fast response

We come to you to perform all services, typically within two weeks and completed the same day

Low cost

Our refurbishment services are cheaper than buying new or sending out for a regrind

Minimal downtime

We have serviced and installed hundreds of ball screws at manufacturer's facilities

Ballscrew Repair Services

Ballscrew Guys provide low cost, fast-response, on-site ball screw repair and refurbishment services for your Shin Nippon Koki (SNK) Lathes and Machining Centers. Call (877) 768-4064 for immediate consultation.

  • Ball Screw Repair and Refurbishment
  • Ball Screw Installation and Removal
  • Ball Screw End Bearing Replacement
  • Linear Way Guide Rail Installation
  • Linear Way Guide Block Repair and Refurbishment

Gallery

SNK FSP-120v 5-axis Vertical Machine Center

Expert service on massive 5-axis VMC.

Ballscrew Guys was called in to do X-Axis and Y-Axis service to Shin Nippon Koki SNK FSP-120v 5-axis profiler vertical machine center (VMC). This thing is a beast, weighing in at over 90,000 lbs. We will be straightforward with you. This machine is challenging from a mechanical standpoint. It takes some serious mechanical surgery to access and refurbish all the ball screws. Because of this, this job requires more man hours than most of our other machine center services.

FANUC controller on SNK FSP-120v.

FANUC controller on a Shin Nippon Koki SNK FSP-120v 5-Axis profiler vertical machine center. While dated, the FANUC systems are pretty much straightforward. After having the ballscrews refurbished, it will be necessary to calibrate and rehome each of the machine axes.

Challenging ball screw service beneath VMC.

Ball screw service on a Shin Nippon Koki SNK FSP-120v 5-Axis profiler vertical machine center (VMC). It is no exaggeration to state that everything about servicing the end bearings and ball screws on this machine is a pain in the ass. This is an image underneath the milling head tower. The ball screw assembly is encased in a yoke mounting system where the bolts are nearly unreachable. To make things worse, there are machined alignment pins which have to be removed as well to facilitate removal of the ball screw mounting yoke. This image is visually interesting as it has a mirror reflection of lubrication oil under the ball screw assembly.

Ball screw service on Y-Axis VMC.

Shin Nippon Koki SNK FSP-120v 5-Axis Profiler Vertical Machine Center (VMC) ball screw service. This is the ball screw assembly from underneath the machining tower. Believe referred to as the Y-Axis. Removing the ball nut yoke was required to create access for ball screw service. This was not an easy task by any means, but Ballscrew Guys were able to get it done.

Destroyed wrench from SNK service.

We have done quite a few Shin Nippon Koki machine tools over the decades, some of which are shown here on the Ballscrew Guys gallery page. One consistent thing we have found with almost all SNK machines we service: The assembly technicians set their torque wrenches to “ridiculous.” The sheer number of foot-pounds or Newton-meters put on SNK ball screws is insane. This SNK FSP-120v 5-Axis profiler vertical machine center (VMC) is no different. Here is the picture of one of the wrenches destroyed in service of an SNK machine.

See All Galleries

Models

Ballscrew Guys provide low cost, fast-response, on-site ball screw repair and refurbishment services for your Shin Nippon Koki (SNK) Lathes and Machining Centers. Call (877) 768-4064 for immediate consultation.

Shin Nippon Koki (SNK)

Type Series Models
Machining Centers Gantry Machining Centers HF-10M HF-3M RB-2N RB-5M RB-5VM RB-6VM RB3-NSM
Lathes - SLX-100 SUT-10 SUT-70
Machining Centers Vertical Machining Centers FSP-50V FSP-120V FSP-80V HPS-120B PC-60V 5-Axis
 
Top